Welcome

*****Skyote #88 gets Bronze Lindy for "Airventure-Oshkosh 2016 Plans Built Champion"******


October, 2007

Welcome to "Skyotelog", the build record of Skyote #88. I assume that you are familar with the Skyote biplane. If not, you should visit http://www.skyote.org/ for a complete introduction to this unique but elusive biplane.

The posts are presented in reverse chronological order (newest first). Or you can click on one of the "Labels" to see all of the posts concerning a specific topic. Click on any photo for a larger image.

All my building experience is limited to Van's RV's so I have no experience with building tube and fabric or "plans building". I have much to learn so take everything I write with a grain of salt and reasonable skepticisim.


I do not intend to follow a "traditional" path for the construction of #88. I intend to employ low level technology and $ to reduce the construction time and difficulty where possible and practical. By low level technology I am referring to CAD, laser, waterjet, CNC. For example:

  • I have purchased a complete wing spar kit from Jerry Kerr.
  • A rib kit from Mr. Bartoe.
  • Brunton Flying Wires and Drag wires from Harvey Swack.
  • CNC profiled tube kits for the fuselage, tail feathers and landing gear from VR3.

In addition I have converted all of the wing fittings, brackets, links, lugs etc. to CAD and had them cut by water jet. I have designed a laser cut wing spar drill template/jig which positions the five spar components so that all of the holes can be drilled in a complete spar as an assembly. I plan to continue converting as many parts as I can to CAD so that I can reduce the "hand-made" components to a minimum.

Note: As of June 2015 I have over 100 CAD files which provide 600+ water jet cut parts for the Skyote.


While it takes a little time, converting the design to CAD is a great way to truly understand the drawings. plus a huge amount of information has been extracted from the rather complex drawings. This can be a great help to others in understanding and interpreting the design.


The Skyote is uniquely suited for conversion to CAD in that a "computer" was used in it's original design. I have read that Mr. Bartoe used a HP calculator to "compute" the design and dimensions of the Skyote. The plans show all of the critical dimensions to three decimal places for X,Y and Z axes.


Amazingly, when I put the design into CAD the resulting 3D models agree with Mr. Bartoe's thee decimal place dimensions about 99.9% of the time. I have found one discrepancy but less than 0.030"!


If you want to build your Skyote as cheaply as possible, or if you enjoy handcrafting the same parts over and over again then my approach to building is not for you!


If you want to build your Skyote in the minimum possible time with highly accurate parts then this approach may be the answer. I personally get a lot of satisfaction out of organizing the project so that it can be produced accurately. Hopefully some of this work will prove useful to others in the future.


Comments are welcome. I will respond as time permits

To receive email notices of new posts just enter your email address in the block at the left. It will be confidential, only Google will know!

Saturday, September 19, 2015

Fourth Wing Painted and Top Wings Striped The end is in Sight!








 Well, the fourth wing is finally painted and both top wings have "Cruiser Orange" stripes.
A little vision hiccup kept me out of the paint booth for about three months but all is well now.The stripes turned out nicely. We pulled the tapes at just the right time so the edges healed over nice and smooth.




The lower wings are hung , just waiting on the upper wing stripes to cure. Actually due to schedule conflicts, we likely won't hang the upper wings before late next week. No matter, there are plenty of details to look after.  My hangar buddy and friend Tom Dubes  (that's his RV4 in Team AeroDynamics livery in the background) has been a tremendous help keeping the fires burning while I was down for maintenance.

Much has been accomplished since my last report Mostly by Tom with me helping a little.

  • The elevator and rudder controls rigged
  • Brakes topped up and pressure tested
  • Fuel tanks flushed and leak tested.
  • All avionics wiring completed and tested.
  • Engine breather piping installed.
  • Fuel tanks flow tested (again).
  • Prop mounted.
  • Primer pump installed.
  • Belite fuel gauge  for fuselage tank installed and wired. This uses the new pressure transducer which makes for a very easy installation.

The major items left to do include making and installing the wing root fairings and some re-work on the ailerons which don't fit to the standard of the rest of the airplane.  We will likely wind up with a "matched hole" aileron kit as the result of the rework.

This is a very busy time with much progress being made on the Matched hole spar kit, welded fuselage kits, etc.  I will post as often as I can find the time but it might be a little spotty.





No comments: